NACE-CIP1-001 Braindumps PDF, NACE NACE-CIP1-001 Exam Cram
New 2022 NACE-CIP1-001 Sample Questions Reliable NACE-CIP1-001 Test Engine
NEW QUESTION 14
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept the assignment without hesitation
- B. Review the NACE Attestation prior to making a decision
- C. Meet with the prospective employer to determine the scope of your role
- D. Advise the prospective employer that you cannot accept the position
Answer: C
NEW QUESTION 15
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When specifically identified in the owner's specification
- C. On every job
- D. When ISO abrasive blast standards are specified
Answer: B
NEW QUESTION 16
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Be trained on how to use the instrument
- C. Ensure the instrument is within calibration parameters
- D. a), b) & c)
Answer: D
NEW QUESTION 17
Passivation can best be described as:
- A. Complete elimination pf the corrosion process
- B. A protective metallic oxide surface layer that slows corrosion
- C. Treating metal with a liquid inhibiter
- D. A coating layer applied to the surface to inhibit corrosion
Answer: B
NEW QUESTION 18
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To dissolve the resin
- C. To promote faster cure
- D. To control the evaporation rate
Answer: D
NEW QUESTION 19
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. the highest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to the air temperature.
Answer: B
NEW QUESTION 20
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION 21
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The inspection cost will be offset by an improvement in service life
- C. The Inspector will improve job flow and schedule
- D. a) and c)
Answer: D
NEW QUESTION 22
Silicone coatings are typically:
- A. Applied in very' thin films
- B. Used as a sacrificial primer
- C. Applied in very thick films
- D. Used strictly in immersion service
Answer: A
NEW QUESTION 23
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Purchase Professional Liability Insurance prior to job commencement
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- D. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
Answer: D
NEW QUESTION 24
The Inspector should record the serial numbers of inspection instruments:
- A. Only if the instrument is suspected of not working properly
- B. Only when verifying accuracy of the instrument
- C. Each time the instrument is used
- D. Only if the specification requires it
Answer: C
NEW QUESTION 25
Digital hygrometers
- A. are used to measure temperature from a distance.
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. determine relative humidity, air temperature, and dew point temperature:
Answer: D
NEW QUESTION 26
ISO SA 2 is defined as:
- A. Near White Metal Blasting
- B. Very Thorough Blast Cleaning
- C. Thorough Blast Cleaning
- D. Light Blast Cleaning
Answer: C
NEW QUESTION 27
An inspectors personal log book should contain:
- A. The inspector's personal opinions of the application team
- B. No comments regarding the application team
- C. Subjective comments re ding the application team
- D. Objective comments regarding the application work
Answer: B
NEW QUESTION 28
Upon arrival of coating materials, the inspector should
- A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B. observe and document the amount of material and batch numbers.
- C. observe and document time frame and environmental conditions between each coat.
- D. observe aryl document that the applicator WFT at regular intervals during application.
Answer: B
NEW QUESTION 29
A magnetic pull-off type gauge is a good choice when:
- A. When an intrinsically safe tool is required
- B. Accuracy is not required
- C. Performing an adhesion test
- D. When working on non-ferrous metals
Answer: A
NEW QUESTION 30
Osmotic blistering is most likely to occur as a result of
- A. overcoating a surface contaminated with chemical salts.
- B. applying tine coating too thin.
- C. inadequate anchor pattern/surface profile.
- D. airless spray application
Answer: D
NEW QUESTION 31
......
Feel NACE NACE-CIP1-001 Dumps PDF Will likely be The best Option: https://www.examboosts.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
NACE-CIP1-001 exam torrent NACE study guide: https://drive.google.com/open?id=1RbEYEChm4B9ICTlGzVuj1oLyM65qXHD4